Portable Handheld Li-ion 18650 Battery Spot Welder Machine 5Gears + Nickel Strip

Description

Store Categories
Store Categories
Other
Product View
Details
1: Five-level power adjustable, four-level power display. Simple and convenient, powerful
2: 5V charging, it can be soldered more than 800 times once fully charged
3: Nickel tape is delivered to the spot welding machine, which can be held with one hand and is easy to use
4: Anti-short-circuit design, if the welding head is short-circuited, only one welding output is output, and the next output can be output after disconnecting again.
5: Support 0.1~0.15mm thick nickel sheet, support 0.2mm nickel sheet welding in fully charged state, intelligent identification, automatic welding, simple and convenient operation
Notice:
Copper and aluminum surfaces cannot be welded, rusted surfaces cannot be welded, and smooth stainless steel surfaces can be welded normally.
One electrode of some batteries is stainless steel and the other electrode is aluminum. Our spot welding machine can weld stainless steel electrodes, and aluminum electrodes need ultrasonic welding. Please pay attention.
Again, aluminum electrodes and copper electrodes cannot be welded.
Common round batteries such as 18650 and 32650 can be welded. The two needles are pressed steadily on the nickel sheet to output welding, lift up, and then weld the next time.
Welding method: Check the welding head visually, hold it at 60° to the horizontal plane, press the two needles on the surface of the nickel sheet at the same time, and the contact is good, the current flows from one needle to the other needle, and the high current melts the nickel sheet, Thereby, the battery and the nickel sheet are welded successfully.
Spot Welder Operation Guide
1. Short press to power on, long press to power off, and no operation for 6 minutes will automatically power off.
2. Support nickel sheet thickness 0.1-0.15mm.
3. After power on, the product is in automatic welding mode, welding once every 2 seconds.
4. When the welding head detects that it touches the metal, it can output it once, and then lift it up to weld the next time.
5. Ensure that the battery welding surface is free of rust, clean and flat.
6. Make sure the nickel sheet is clean and flat.
7. Set up the spot welding machine and press it properly so that the welding pin and the nickel sheet, the nickel sheet and the battery are in good contact, and there is no dangling and no bad contact, so that the welding can be done well. Different nickel thickness, different gears are not the better the effect of higher power, users can try which gear is more suitable.
8. Use Android mobile phone charger to charge, 5V input (higher voltage is strictly prohibited), charging current 1A, it is recommended to use 5V/2A charger. This product supports use while charging.
9. After turning on the machine, the output power of the spot welding machine can be changed by short pressing the button, and the blue light indicates the gear.
switch machine
Short press to power on
long press to power off
6 minutes without any operation will automatically shut down
Welding parameters
Maximum output current up to 1200A
Fully charged for more than 1000 continuous welds
Five gears of power can be adjusted, short press the button to control, blue light indicator
Charge
Use Android mobile phone charger to charge, 5V input (higher voltage is strictly prohibited), charging current 1A, it is recommended to use 5V/2A charger
This product supports use while charging
Remaining power indicator: green (high), green flashing (medium high), red flashing (medium low), red (low), red light must be charged before it can work. Low battery will affect the welding effect
Shipping list:
Spot Welder X1
Nickel Strip X1
Manual X1
Shipping Policy
Payment Method
Returns Policy
Shipping Policy
Payment Method
Returns Policy
Home
Payment
Shipping
About us
Contact us
Copyright©2018 datacaciques
Home
Payment
Shipping
About us
Contact us
Store Categories
Store Categories
Other
Product View
Details
1: Five-level power adjustable, four-level power display. Simple and convenient, powerful
2: 5V charging, it can be soldered more than 800 times once fully charged
3: Nickel tape is delivered to the spot welding machine, which can be held with one hand and is easy to use
4: Anti-short-circuit design, if the welding head is short-circuited, only one welding output is output, and the next output can be output after disconnecting again.
5: Support 0.1~0.15mm thick nickel sheet, support 0.2mm nickel sheet welding in fully charged state, intelligent identification, automatic welding, simple and convenient operation
Notice:
Copper and aluminum surfaces cannot be welded, rusted surfaces cannot be welded, and smooth stainless steel surfaces can be welded normally.
One electrode of some batteries is stainless steel and the other electrode is aluminum. Our spot welding machine can weld stainless steel electrodes, and aluminum electrodes need ultrasonic welding. Please pay attention.
Again, aluminum electrodes and copper electrodes cannot be welded.
Common round batteries such as 18650 and 32650 can be welded. The two needles are pressed steadily on the nickel sheet to output welding, lift up, and then weld the next time.
Welding method: Check the welding head visually, hold it at 60° to the horizontal plane, press the two needles on the surface of the nickel sheet at the same time, and the contact is good, the current flows from one needle to the other needle, and the high current melts the nickel sheet, Thereby, the battery and the nickel sheet are welded successfully.
Spot Welder Operation Guide
1. Short press to power on, long press to power off, and no operation for 6 minutes will automatically power off.
2. Support nickel sheet thickness 0.1-0.15mm.
3. After power on, the product is in automatic welding mode, welding once every 2 seconds.
4. When the welding head detects that it touches the metal, it can output it once, and then lift it up to weld the next time.
5. Ensure that the battery welding surface is free of rust, clean and flat.
6. Make sure the nickel sheet is clean and flat.
7. Set up the spot welding machine and press it properly so that the welding pin and the nickel sheet, the nickel sheet and the battery are in good contact, and there is no dangling and no bad contact, so that the welding can be done well. Different nickel thickness, different gears are not the better the effect of higher power, users can try which gear is more suitable.
8. Use Android mobile phone charger to charge, 5V input (higher voltage is strictly prohibited), charging current 1A, it is recommended to use 5V/2A charger. This product supports use while charging.
9. After turning on the machine, the output power of the spot welding machine can be changed by short pressing the button, and the blue light indicates the gear.
switch machine
Short press to power on
long press to power off
6 minutes without any operation will automatically shut down
Welding parameters
Maximum output current up to 1200A
Fully charged for more than 1000 continuous welds
Five gears of power can be adjusted, short press the button to control, blue light indicator
Charge
Use Android mobile phone charger to charge, 5V input (higher voltage is strictly prohibited), charging current 1A, it is recommended to use 5V/2A charger
This product supports use while charging
Remaining power indicator: green (high), green flashing (medium high), red flashing (medium low), red (low), red light must be charged before it can work. Low battery will affect the welding effect
Shipping list:
Spot Welder X1
Nickel Strip X1
Manual X1
Shipping Policy
Payment Method
Returns Policy
Shipping Policy
We will arrange shipping for you within 24 Hours after payment cleared except the holidays.
-We ship items to Worldwide. Thank you!
-we will ship out the order in 1-2 business days after payment cleared .Since it is international shipping ,delivery time is about 15--28 business days to arrive to most countries.
Payment Method
We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase.
2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances.
3.Buyers are responsible for import duties,custom fees and taxes, if any, please check your country.
Returns Policy
1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase.
2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse.
3. Please include your eBay ID and item number with any email requests.